Ohm’s Law Calculator
Enter any two of voltage, current, resistance and power, and the calculator works out the other two.
How to use the Ohm’s law calculator
Fill in any two boxes and pick the units. The other two values appear below. If you fill in more than two, the calculator uses the two you changed most recently. Use Clear all to start again.
The Ohm’s law formula
Ohm’s law links the voltage across a resistor, the current through it and its resistance:
V = I × R
Rearranged, I = V / R and R = V / I. Add the power formula P = V × I and you can find any of the four values from any two.
| You know | Voltage V | Current I | Resistance R | Power P |
|---|---|---|---|---|
| V and I | – | – | V / I | V × I |
| V and R | – | V / R | – | V² / R |
| V and P | – | P / V | V² / P | – |
| I and R | I × R | – | – | I² × R |
| I and P | P / I | – | P / I² | – |
| R and P | √(P × R) | √(P / R) | – | – |
Worked examples
Current through a resistor
12 V across a 1 kΩ resistor: I = 12 / 1,000 = 0.012 A = 12 mA. The power is 12 × 0.012 = 0.144 W.
Resistance from a measurement
A heater draws 2 A from 24 V: R = 24 / 2 = 12 Ω, using 48 W.
Current from a power rating
A 1/4 W, 1 kΩ resistor can safely carry at most I = √(0.25 / 1,000) = 15.8 mA. In practice, stay well below that.
Watch the units
Most mistakes come from mixing units. Ohm’s law works directly in volts, amps and ohms. A current of 20 mA is 0.02 A, and 4.7 kΩ is 4,700 Ω. The unit menus in the calculator do this conversion, so you can enter values as they appear on a schematic.
Where Ohm’s law applies
Ohm’s law describes resistors very well, and wires and heating elements fairly well. It does not describe LEDs, diodes or transistors, whose current does not rise in proportion to voltage. That is why an LED needs a series resistor. See the LED resistor calculator. For several resistors at once, combine them first with the series or parallel calculator, or use the voltage drop calculator for a series string.
Frequently asked questions
What is Ohm’s law in simple terms?
The current through a resistor rises in step with the voltage across it. Double the voltage and the current doubles. The resistance sets how much current you get for each volt.
How do you calculate the current through a resistor?
Divide the voltage across the resistor by its resistance: I = V / R. Our guide on calculating the current through a resistor goes through series and parallel circuits step by step.
Who discovered Ohm’s law?
The German physicist Georg Simon Ohm published it in 1827. The unit of resistance, the ohm (Ω), is named after him.
More calculators
-
Resistor Color Code Calculator
Decode 3, 4, 5 and 6-band resistors, or find the bands for a value.
-
Parallel Resistor Calculator
Total resistance of up to 20 resistors in parallel.
-
Series Resistor Calculator
Add up resistors in series, in any mix of units.
-
LED Resistor Calculator
Current-limiting resistor, standard value and wattage for LEDs.
-
Voltage Divider Calculator
Output voltage, or the resistor needed for a target voltage.
-
Voltage Drop Calculator
Voltage across each resistor in a series circuit.
-
Resistor Power Calculator
Power dissipated in a resistor and the wattage rating to buy.
-
SMD Resistor Code Calculator
Decode 3-digit, 4-digit, R and EIA-96 SMD markings.
-
Standard Resistor Values
Nearest E6 to E192 value for any resistance.