Voltage Divider Calculator

Find the output voltage of a two-resistor divider, or the R1 or R2 value you need for a target voltage, with the nearest standard resistor.

Solve for
V
Output voltage 3.837 V Vout = Vin × R2 / (R1 + R2), with no load connected.
Divider current
816.3 µA
Ratio Vout / Vin
0.3197

How to use the voltage divider calculator

Choose what to solve for. To find Vout, enter the input voltage and both resistors. To design a divider, choose R1 or R2, enter the input and output voltages and the resistor you already have. The result shows the exact value, the nearest standard E24 resistor and the voltage that resistor would actually give.

Voltage divider formula

Two resistors in series share the input voltage in proportion to their values. The output is taken across the bottom resistor, R2:

Vout = Vin × R2 / (R1 + R2)

Rearranged to find a resistor:

R1 = R2 × (Vin − Vout) / Vout
R2 = R1 × Vout / (Vin − Vout)

Worked examples

5 V to 3.3 V logic level

A 5 V signal into a 3.3 V input: with R1 = 1 kΩ, R2 = 1 × 3.3 / (5 − 3.3) = 1.94 kΩ. A standard 2 kΩ gives 3.33 V. Using 10 kΩ and 20 kΩ gives the same ratio with less current. This works for slow signals such as UART receive lines. Fast or two-way buses are better served by a level-shifter chip.

Measuring a 12 V battery with a 3.3 V ADC

To bring up to 14.4 V (a charging lead-acid battery) under 3.3 V, the ratio must be below 3.3 / 14.4 = 0.229. R1 = 47 kΩ and R2 = 12 kΩ gives 0.203, so 14.4 V reads as 2.93 V with some headroom. Multiply the ADC reading by (R1 + R2) / R2 = 4.92 in your code to get the battery voltage back.

Choosing resistor values

  • The ratio sets the voltage, the size sets the current. 1 kΩ + 1 kΩ and 100 kΩ + 100 kΩ both halve the voltage, but the first draws 100 times more current from the source.
  • Low values waste power. A 10 Ω + 10 Ω divider on 12 V draws 600 mA and burns 7.2 W. Check with the resistor power calculator.
  • High values are sensitive to loading and noise. Many microcontroller ADCs want a source resistance of 10 kΩ or less. A small capacitor (around 100 nF) from Vout to ground helps with very high values.
  • Standard values rarely give the exact ratio. Use the result here, or the standard resistor values tool, to pick a practical pair.

The loading effect

The formula assumes nothing is connected to the output. Any load you attach sits in parallel with R2 and pulls Vout down. As a rule of thumb, keep the load at least ten times higher than R2. For a 10 kΩ R2, the load should be 100 kΩ or more. Calculate the combined value with the parallel resistor calculator and use it as the new R2 to see the real output.

Don’t use a divider as a power supply

A voltage divider is for signals and measurements. Its output voltage changes as soon as the load current changes, and it wastes power all the time. To power a circuit at a lower voltage, use a voltage regulator or a DC-DC converter.

Frequently asked questions

What does a voltage divider do?

It produces a fixed fraction of the input voltage using two resistors in series. It is used to scale signals and sensor readings, and to set reference and bias voltages.

What happens if R1 and R2 are equal?

The output is exactly half the input, whatever their value.

Is a potentiometer a voltage divider?

Yes. The wiper splits one resistive track into R1 and R2, and turning the knob changes the ratio.

More calculators