SMD Resistor Code Calculator
Type the code printed on a surface-mount resistor to get its value. Reads 3-digit, 4-digit, R-notation and EIA-96 codes.
How to read SMD resistor codes
Surface-mount resistors are too small for color bands, so most have a short code printed on top. Type the code into the calculator as you see it. It recognizes four marking systems.
3-digit code
Used on standard ±5% parts. The first two digits are the value and the third is the number of zeros to add.
- 103 = 10 followed by 3 zeros = 10,000 Ω = 10 kΩ
- 472 = 4,700 Ω = 4.7 kΩ
- 220 = 22 followed by no zeros = 22 Ω (not 220 Ω)
4-digit code
Used on ±1% parts. The first three digits are the value and the fourth is the number of zeros.
- 1002 = 100 followed by 2 zeros = 10 kΩ
- 4701 = 4,700 Ω = 4.7 kΩ
- 1000 = 100 Ω
R notation for small values
The letter R marks the decimal point:
- 4R7 = 4.7 Ω
- R10 = 0.10 Ω, a typical current-sense resistor
- 0R or 000 = a 0 Ω link, used as a jumper
EIA-96 code
Very small ±1% resistors (0603 size and below) often have only three characters: two digits and a letter. The two digits are not the value itself but a position (01 to 96) in the E96 series of standard values, and the letter is the multiplier.
| Letter | Multiplier |
|---|---|
| Z | ×0.001 |
| Y or R | ×0.01 |
| X or S | ×0.1 |
| A | ×1 |
| B or H | ×10 |
| C | ×100 |
| D | ×1,000 |
| E | ×10,000 |
| F | ×100,000 |
For example, 01C: code 01 is 100 in the E96 table, and C means ×100, so 10 kΩ. 68X: code 68 is 499, and X means ×0.1, so 49.9 Ω.
A code like 10R is read here as 10 Ω (R notation), which is far more common than the rare EIA-96 multiplier R.
Unmarked SMD resistors
Many 0402 and smaller resistors have no marking at all. The only way to find their value is from the circuit’s bill of materials, or by measuring with a multimeter. Measure out of circuit if you can, because other parts in parallel will affect the reading.
Frequently asked questions
What does 103 mean on an SMD resistor?
10 followed by three zeros: 10,000 Ω, or 10 kΩ.
What does 000 mean on an SMD resistor?
It is a 0 Ω resistor, also called a zero-ohm link. It is used as a jumper that pick-and-place machines can fit like any other part.
How can I tell a 3-digit code from an EIA-96 code?
A 3-digit code is all numbers, such as 472. An EIA-96 code always ends in a letter, such as 01C or 68X.
More calculators
-
Resistor Color Code Calculator
Decode 3, 4, 5 and 6-band resistors, or find the bands for a value.
-
Parallel Resistor Calculator
Total resistance of up to 20 resistors in parallel.
-
Series Resistor Calculator
Add up resistors in series, in any mix of units.
-
LED Resistor Calculator
Current-limiting resistor, standard value and wattage for LEDs.
-
Ohm's Law Calculator
Enter any two of voltage, current, resistance and power.
-
Voltage Divider Calculator
Output voltage, or the resistor needed for a target voltage.
-
Voltage Drop Calculator
Voltage across each resistor in a series circuit.
-
Resistor Power Calculator
Power dissipated in a resistor and the wattage rating to buy.
-
Standard Resistor Values
Nearest E6 to E192 value for any resistance.